Gear guide 06
Shopping for dab gear in LA
Updated November 1, 2026
Short answer
Look closely at joints and welds, ask what size and gender the joint is, and handle the piece before you buy it. Spend more on the banger and torch than you think you should, and less on the rig. If an e-rig is priced way below everywhere else, or the box and serial number look off, walk away.
Buying dab gear in Los Angeles is easy; buying good dab gear takes a trained eye. This guide covers how to read a glass case, spot cheap imports, what to ask before you pay, general price ranges, buying used, and the red flags that mean walk away.
On this page
The LA gear situation
LA has no shortage of places to buy dab gear. You will find glass in smoke shops on almost every major street, plus head shops, glass galleries, and glass shows that come through town. Some shops carry serious work from respected glassblowers. Others mostly carry cheap imports with nice lighting.
Both can be fine. Cheap glass is not always bad, and expensive glass is not always good. The point of this guide is to help you tell the difference in person, so you pay for quality and not for marketing.
This site never recommends specific stores. Shops change, staff change, and a good shop for one person is not always good for the next. The skills below work everywhere.
Reading a glass case
When you look at a case of rigs and bangers, here is what to check before anything else.
Joints
The ground part of the joint should be evenly frosted all the way around. No chips, no rough spots, no shiny patches. Ask to try a banger in it. It should seat smoothly and not rock.
Welds
Where two pieces of glass meet, the seam should look smooth, even and clean. Lumpy, sharp, pinched or thin welds are weak spots where cracks start.
Glass thickness
Look at the edge of the mouthpiece or the joint opening. You can see the wall thickness there. It should be consistent. Very thin glass on a cheap piece is a red flag. Thicker is generally more durable, but thickness alone does not mean quality.
Base
Ask to set it on the counter. It should sit flat and not wobble. Tap the top gently. It should not tip.
Bubbles and inclusions
Small bubbles in colored sections are normal. Big bubbles or debris near a joint or weld are not.
Quartz bangers
Hold the banger up to the light. Clear quartz should look like clear glass. Milky, bubbly or hazy quartz is lower quality. Check where the arm meets the bucket; the weld should be clean and even. The floor should be flat and level.
Bring your own banger to test joint fit, or at least know your rig's joint size and gender before you walk in. It saves a lot of guessing.
Spotting cheap imports
Mass-produced imported glass is everywhere. Some of it is decent for the price. A lot of it is not. Signs of low quality:
- Thin, uneven glass. Especially around joints and the base.
- Rough joints. Poorly frosted, chipped or out of round.
- Sloppy welds. Lumps, sharp edges or visible gaps.
- Too many percs for the price. Complex glass done cheaply usually means corners were cut.
- Identical pieces in big stacks. Mass production is not bad by itself, but check quality closely.
- Copies of artist designs. Knockoffs of famous artist styles are common.
The upside: cheap glass can be a good way to learn. A simple, well-checked import rig with a good banger can make great dabs. Just check the joints and welds.
Questions to ask
- What is the joint size and gender? You need to know this for every banger and accessory you buy.
- Who made it? A shop that knows the maker usually cares about quality.
- Can I try a banger in the joint? Fit matters.
- What is your return or exchange policy for defects? Ask before you pay, not after.
- For e-rigs: is this from an authorized seller, and does the warranty apply? Many brands only honor warranties through authorized sellers.
- For bangers: what is the bottom thickness and bucket size? So you can match a cap.
General price ranges
Prices change and vary a lot between shops, so these are broad ranges only.
| Item | Budget | Solid | High end |
|---|---|---|---|
| Dab rig | Tens of dollars | Around one hundred to a few hundred | Hundreds to thousands for artist glass |
| Quartz banger | Under twenty | Twenty to around fifty | More for premium styles |
| Carb cap | A few dollars | Ten to thirty | More for artist caps |
| Butane torch | Around twenty | Thirty to sixty | Rarely needed |
| E-rig | Low hundreds | A few hundred | Several hundred and up |
Honest advice: the best value is a solid mid-range banger and torch with a simple rig. That combo outperforms an expensive rig with a cheap banger every time.
Buying used gear
Used glass and e-rigs can be good deals. Check carefully.
Used glass
- Inspect it under bright light for hairline cracks, especially at joints, welds and the base.
- Check that the joint is not chipped.
- Expect to deep clean it before use.
- Never buy used bangers unless you can verify they are not cracked or badly devitrified. They are cheap enough new.
Used e-rigs
- Ask how old it is and how much it was used. Batteries wear out.
- Test it if you can. It should heat and cycle normally.
- Check that replacement chambers are still available for that model.
- Do not assume the warranty transfers. It often does not.
- Replace the chamber right away. You do not know how it was treated.
Red flags
Walk away if you see any of these:
- An e-rig priced far below everywhere else. Counterfeit e-rigs exist. Check the box, the serial number, and the brand's site for how to verify.
- Cracks, chips or fractures anywhere. Even small ones get worse with heat.
- Big claims with no details. If a banger is sold as amazing but nobody can tell you the thickness, that tells you something.
- No defect policy. A shop should stand behind obvious defects.
- Pressure to buy now. Good gear will still be there tomorrow.
- A banger that does not sit level. Oil will pool.
Do not buy the biggest, most complicated rig in the case as your first piece. It tastes worse, cleans worse and breaks easier. Start simple.
The shopping list for a first setup
If you are starting from scratch, here is what to bring home:
A small rig with a 14mm female joint
One simple perc, stable base, clean welds.
A quartz flat-top banger
Matching joint, around 25mm bucket, 3 or 4mm bottom.
A carb cap that fits the bucket
Directional or bubble.
A butane torch and refined butane
Adjustable flame, safety lock.
A dab tool, cotton swabs and isopropyl
The basics for dabbing and cleaning.
A silicone mat
Protects your table.
Then read the banger guide to understand what you bought, and the torch guide to learn how long to heat it.
Also useful: 14mm vs 18mm vs 10mm joints, Peak Pro 3DXL vs Switch², Dab safety.