LA Dab Guide

Technique guide

How to dab, step by step

Updated November 1, 2026

Short answer

To dab with a torch, heat an empty quartz banger, turn off the torch, wait for it to cool, drop in a rice-grain-sized dab, cap it and pull slowly. On an e-rig, you load a small dab, cap it and press a button. Either way, finish by swabbing while it is still warm.

This is the full routine for a first dab, written out once for a torch and banger and once for an e-rig.

On this page
  1. What you need
  2. How to dab with a torch and banger
  3. How to dab with an e-rig
  4. How big should a first dab be?
  5. If it goes wrong

What you need

For a torch setup: a dab rig, a quartz banger that fits its joint, a carb cap that fits the bucket, a butane torch, a dab tool, cotton swabs and a silicone mat. For an e-rig, the device covers most of that. You still want a tool and swabs.

How to dab with a torch and banger

  1. Set up on a stable surface

    Put the rig on a silicone mat, toward the back of the table. Fill it so the water just covers the perc or downstem holes. Open a window or run a fan.

  2. Load your tool

    Pick up a small dab, about the size of a grain of rice, and keep the tool within reach. Have your carb cap ready too.

  3. Heat the banger

    Heat the floor of the empty banger with the flame moving in small circles. A flat top usually takes about 20 to 45 seconds, depending on thickness. Stop well before it glows.

  4. Turn the torch off and wait

    Lock the torch and set it down. Wait about 25 to 60 seconds for a flat top. The cool-down timer gives you a starting number.

  5. Drop the dab and cap it

    Touch the tool to the banger floor so the dab rolls off, then cap the banger right away.

  6. Pull slowly

    Inhale slow and steady, like sipping through a straw. Rotate a directional cap to move the oil around the floor.

  7. Swab while warm

    Wait a few seconds, then wipe out the banger with a dry cotton swab. The leftover oil comes right out. Leave the banger alone until it has cooled, since quartz stays hot for minutes.

Easier first dab

A cold start skips the wait: you load the dab into a cold banger, cap it, then heat until you see the first vapor. It is the easiest way to get a low-temp dab without timing anything.

How to dab with an e-rig

  1. Fill the glass

    Add water to the glass attachment until it just covers the holes, or to the fill line if there is one.

  2. Load the chamber

    Drop a small dab in the center of the chamber floor. Keep it off the walls.

  3. Cap it and pick a low setting

    Put on the cap and start on a low setting. You can go up on the next dab, but you cannot get burned-off flavor back.

  4. Start the heat cycle

    Start the cycle the way your manual shows, and wait for the light or vibration that says it is ready.

  5. Pull slowly

    Long, slow pulls work best. Hard pulls can drag oil out of the chamber.

  6. Swab while warm

    Wipe the chamber with a dry cotton swab after the dab, then check your manual for the deeper cleaning routine.

How big should a first dab be?

Start with about the size of a grain of rice, and wait a few minutes before taking another. Concentrates are strong, and a small dab hits much harder than a bowl of flower. Small dabs also taste better and vaporize more completely.

If it goes wrong

A sharp, burning hit usually means the banger was too hot, so wait longer next time. A puddle left behind usually means it cooled too much, so wait less. The fix my dab tool walks through the rest. For burns, torch habits and what to do if you take too much, read dab safety. Do not drive after you dab.